Wall-mounted belt unit
The belt on the wall, with the floor left clear
A small housing screwed to the wall and a printed belt that crosses the opening when you need it. In 3, 6 and 9 metres, from one unit, with your design and the housing in four colours.
From €63.67 per unit · excl. VAT · Shipping extra
There is no box of two and no minimum order: if you need one, we sell you one.
Three, six and nine metres. Beyond six there is almost nothing custom-printed on the market.
Nothing to dodge when sweeping or going past with a pallet truck. When it is not in use, the belt sits inside.
Where it makes sense
In a narrow corridor, on a staircase, in front of a room that closes at certain hours or at the entrance to a warehouse, a post gets in the way more than it helps: it has to be moved, it falls over and it takes up a metre and a half of floor.
The wall unit solves the same problem without touching the floor. It is screwed to the wall at whatever height you want, the belt comes out when you need it and retracts on its own when you do not.
Three, six and nine metres
The 3 metre unit is for doorways, stairs and ordinary corridors. The 6 metre crosses a wide opening or the mouth of a car park. The 9 metre is the one almost nobody has: warehouse aisles, industrial units, loading bays.
The longer the run, the more it shows that the belt has something written on it. Nine metres with your message repeated can be read from the far end of the building.
Your belt, and the housing in its colour
The belt is printed exactly like the one on the post: dye sublimation in full colour, on both sides, with your logo or your notice, and no set-up costs.
The housing comes in black, white, red or yellow at no surcharge, so you can make it disappear against the wall or, the other way round, have it seen from a distance.
How it hooks on the other side
A wall receiver is screwed up opposite: a small plate the belt hook clips into. You can add extra receivers to close the opening in several directions from the same unit.
If you would rather not drill opposite, there is a magnet set that holds the belt on any metal surface: a door, a pillar, a shelving unit.
Colour
Wall-mounted belt unit Specifications
| Models | 3 m · 6 m · 9 m |
|---|---|
| Belt width | 48 mm |
| Unit size | 18 × 10 cm (3 and 9 m) · 13.5 × Ø 9 cm (6 m) |
| Weight | 0.5 kg (3 m) · 1 kg (6 m) · 1.2 kg (9 m) |
| Fixing | M6 screws included |
| Housing colours | Black, white, red and yellow, no surcharge |
| Spring cycles | 200,000 |
| Accessories | Extra wall receiver · magnet set |
| Warranty | 2 years (statutory warranty) |
Sample
Feel it before you order.
We send you a piece of printed belt so you can check the feel, the colour and the quality before deciding. Free, with no obligation.
FAQ Questions.
What height should it go at?
Between 90 cm and a metre off the floor, which is the belt height on a post. If what you want is for it to be seen rather than ducked under, a little higher works better.
Will it hold on any wall?
It comes with M6 screws for solid walls. On plasterboard or hollow partitions you need the right anchor: the unit weighs little, but the belt pulls when somebody pushes it.
What if I cannot drill opposite?
With the magnet set the belt holds on any metal surface. You can also fit two units facing each other and hook one to the other.
Can I order just one?
Yes, from one unit. There is no box of two as with the posts.
Is the 9 metre one printed too?
Yes, and that is where it shows most. It is printed along its whole length, in full colour and on both sides, just like the short ones.
Customisation
Custom belt
Your logo printed on the belt
Keep reading →
Custom post tube
The post, in your brand colour
Keep reading →
Custom cap
Your logo on the cap as well
Keep reading →
Belt barrier post
The belt barrier post that carries your brand
Keep reading →
Sign holder
The sign, at eye level
Keep reading →